3:28:36 PM.
Address: /showpage.php~file=06350300.htm.html
Title: Section 3503  •  Size: 39582

Go to Table of Contents
Go to previous section: 3502

SECTION 3503 - RECOGNIZED STANDARDS

The standards listed in Part III of this chapter are recognized standards. Compliance with these recognized standards shall be prima facie evidence of compliance with the standard of duty set forth in Section 3502.

Part II-U.B.C. Standards

U.B.C. STD. AND
SEC. NO.
TITLE AND SOURCE

CHAPTER 2

2-1; 201.2, 215

Noncombustible Material-Tests. Standard Method of Test E 136-79 of the ASTM.*

CHAPTER 4

4-1; 303.8, 405.1.1, 405.3.4

Proscenium Firesafety Curtains. Installation Standard of the International Conference of Building Officials.

CHAPTER 7

7-1; 405.1.1; 405.3.4; 601.3; 703.2; 703.4; 706; 709.3.2, Item 2; 709.5; 709.6; 709.7, Item 2; 710.2; 710.3; Table 7-A; 2602.5.2

Fire Tests of Building Construction and Materials. Standard Methods E 119-83 of the ASTM.

7-2; 302.4, 305.2.2.2, 703.4, 713.5, 713.9, 713.10, 1005.8, 1009.3

Fire Tests of Door Assemblies. Standard 10B-1988 of the Underwriters Laboratories Inc. and International Conference of Building Officials Test Standard for Smoke- and Draft-Control Door Assemblies.

7-3; 703.4, 713.5

Tinclad Fire Doors. Specification of the American National Standards Institute/Underwriters Laboratories Inc. 10A-1979 (R 1985).

7-4; 703.4, 713.5, 713.9

Fire Tests of Window Assemblies. Standard Methods E 163-76 of the ASTM.

7-5; 703.4, 714

Fire Tests of Through-penetration Fire Stops. Standard Method E 814-83 of the ASTM.

7-6; 703.4, 704.6, 1701.1, 1701.4

Thickness and Density Determination for Spray-applied Fireproofing. Test Standard of the International Conference of Building Officials.

7-7; 703.3, 703.4

Methods for Calculating Fire Resistance of Steel, Concrete, Wood, Concrete Masonry and Clay Masonry Construction. Standard of the International Conference of Building Officials.

7-8; 410, 1001.1, 1004.8

Horizontal Sliding Fire Doors Used in an Exit. Test Standard of the International Conference of Building Officials.

CHAPTER 8

8-1; 201.2; 207; 215; 217; 405.1.1; 405.3.4; 601.3; 707.2; 707.3; 801.2; 802.1, Item 1; 802.2; 2602.3; 2602.5.2; 2602.6

Test Method for Surface-burning Characteristics of Building Materials. Standard Test Method E 84-84 of the ASTM.

8-2; 801.2, 805

Standard Test Method for Evaluating Room Fire Growth Contribution of Textile Wall Covering. Test Method of the International Conference of Building Officials.

CHAPTER 9

9-1; 372.2, 403.2, 404.3.1, 405.1.1, 405.3.4, 409.3, 804.1, 902, 904.1.2, 904.1.3, 904.2.6.3, 904.2.7, 904.2.8, 2603.7.1, 2603.8.1

Installation of Sprinkler Systems. Standard for the Installation of Sprinkler Systems, NFPA 13-1991, National Fire Protection Association.

9-2; 902, 904.1.2, 904.5.1

Standpipe Systems.

9-3; 804.1, 805, 902, 904.1.2, 2603.7.1, 2603.8.1

Installation of Sprinkler Systems in Group R Occupancies Four Stories or Less. Standard for the Installation of Sprinkler Systems in Residential Occupancies up to Four Stories in Height, NFPA 13R-1989, National Fire Protection Association.

CHAPTER 10

10-1; 1001.1, 1004.8

Power-operated Exit Doors. Test Standard of the International Conference of Building Officials.

10-2; 1001.1, 1006.16

Stairway Identification. Specification Standard of the International Conference of Building Officials.

10-3; Appendix 3412.1

Exit Ladder Device. Test Standard of the International Conference of Building Officials.

10-4; 1001.1, 1004.4

Panic Hardware. Standard 305, July 30, 1979, of the Underwriters Laboratories Inc.

CHAPTER 14

14-1; 601.3, 1401.2, 1402.1

Kraft Waterproof Building Paper. Federal Specification UU-B-790a (February 5, 1968).

14-2; 1401.2, 1404

Vinyl Siding. Standard Specification D 3679-91 for Rigid Polyvinyl Chloride (PVC) of the ASTM.

CHAPTER 15

15-1; 1501.1, Table 15-E

Roofing Aggregates. Material Standard of the International Conference of Building Officials.

15-2; 601.3, 1501.1, 1502, Table 15-A, 2602.5.3

Test Standard for Determining the Fire Retardancy of Roof-covering Materials. Standard Specification 790 (October 5, 1983) of the Underwriters Laboratories Inc.

15-3; 1501.1, 1502, 1507.2, 1507.12

Wood Shakes. Part I-Wood Shakes (nonpreservative treated). Grading and Packing Rules for Red Cedar Shakes. Grading Rules of the Red Cedar Shingle & Handsplit Shake Bureau, 1975. Part II-Wood Shake Hip and Ridge Units (nonpreservative). Shake and Shingle Council and Material Standard of the International Conference of Building Officials. Part III-Wood Shakes (preservative treated). Grading and Packing Rules for Treated Southern Pine Taper-sawn Shakes. Grading Rules of the Red Cedar Shingle & Handsplit Shake Bureau, 1982, and Material Standard of the International Conference of Building Officials. Part IV-Southern Yellow Pine, Black Gum/Sweet Gum Taper-sawn Shake Hip and Ridge Units. Material Standard of the International Conference of Building Officials.

15-4; 1501.1, 1502, 1507.13

Wood Shingles. Standard of the Red Cedar Shingle & Handsplit Shake Bureau and Material Standard of the International Conference of Building Officials.

15-5; 1501.1, 1502, 1507.7

Roof Tile. Test Standard of the International Conference of Building Officials.

15-6; 1501.1, 1502

Modified Bitumen, Thermoplastic and Thermoset Membranes Used for Roof Coverings. Standard Specifications D 412-87, D 471-79, D 570-81, D 624-86, D 638-84, D 751-79, D 816-82, D 1004-66 (1981), D 1204-84, D 2136-84 and D 2137-83 of the ASTM.

15-7; 906.1, 906.4, 1501.1

Automatic Smoke and Heat Vents. Material Standard of the International Conference of Building Officials.

CHAPTER 18

18-1; 1801.2, 1803.1

Soils Classification. Standard Method D 2487-69 of the ASTM.

18-2; 1801.2, 1803.2

Expansion Index Test. Recommendation of the Los Angeles Section of the ASCE Soil Committee.

CHAPTER 19

19-1; 1903.2.2, 1905.4

Portland Cement and Blended Hydraulic Cements. Standard Specifications C 150-85a and C 595-86 of the ASTM.

19-2; 1903.2.2, 1903.4, 1912.14.3, 1921.2.6

Welding Reinforcing Steel, Metal Inserts and Connections in Reinforced Concrete Construction. Structural Welding Code-Reinforcing Steel ANSI/AWS D1.4-92 of the American Welding Society, Inc.

19-3; 108.5.2, 1701.3, 1903.2.7, 1905.8

Ready-mixed Concrete. Standard Specification C 94-86a of the ASTM.

19-4; 1903.2.7, 1905.8

Concrete Made by Volumetric Batching and Continuous Mixing. Standard Specification C 685-86 of the ASTM.

19-5; 1903.2.7, 1927.1, 1927.3

Mill-Mixed Gypsum Concrete and Poured Gypsum Roof Diaphragms. Standard Specification C 317-70 of the ASTM. Poured Gypsum Roof Diaphragm, based on reports of test programs by S. B. Barnes and Associates, dated February 1955, November 1956, January 1958, and February 1962.

19-6; 1903.2.7

Ground-iron Blast-furnace Slag for Use in Concrete and Mortars. Standard Specification C 989-84 of the ASTM.

19-7; 1903.3

Slump of Portland Cement Concrete. Standard Specification C 143-78 of the ASTM.

CHAPTER 21

21-1; 2102.2, Item 4

Building Brick, Facing Brick and Hollow Brick. (Made from Clay or Shale.) Standard Specifications C 62-87, C 216-86 and C 652-87a of the ASTM.

21-2; 2102.2, Item 6

Calcium Silicate Face Brick (Sand-lime Brick). Standard Specification C 73-75 of the ASTM.

21-3; 2102.2, Item 5

Concrete Building Brick. Standard Specification C 55-75 (1980) of the ASTM.

21-4; 2102.2, Item 5

Hollow and Solid Load-bearing Concrete Masonry Units. Standard Specification C 90-86 of the ASTM.

21-5; 2102.2, Item 5

Nonload-bearing Concrete Masonry Units. Standard Specification C 129-75 (1980) of the ASTM.

21-6; See Uniform Code for Building Conservation.

In-Place Masonry Shear Tests. Test Standard of the International Conference of Building Officials.

21-7; See Uniform Code for Building Conservation.

Tests of Anchors in Unreinforced Masonry Walls. Test Standard of the International Conference of Building Officials.

21-8; See Uniform Code for Building Conservation.

Pointing of Unreinforced Masonry Walls. Construction Specification of the International Conference of Building Officials.

21-9; 2102.2, Item 6

Unburned Clay Masonry Units and Standard Methods of Sampling and Testing Unburned Clay Masonry Units. Test Standard of the International Conference of Building Officials.

21-10; 1903.2.5, 2102.2, 2104.8, 2106.3.9.4.1

Part I-Joint Reinforcement for Masonry. Specification Standard of the International Conference of Building Officials. Part II-Cold-drawn Steel Wire for Concrete Reinforcement. Standard Specification A 82-88 of the ASTM.

21-11; 2102.2, Item 2; Table 21-A

Cement, Masonry. Standard Specification C 91-83a of the ASTM.

21-12; 2102.2, Item 3

Quicklime for Structural Purposes. Standard Specification C 5-79 (1984) of the ASTM.

21-13; 2102.2, Item 3

Hydrated Lime for Masonry Purposes. Standard Specification C 207-79 (Reapproved 1984) of the ASTM.

21-14; 2102.2, Item 2; Table 21-A

Mortar Cement. Test Standard of the International Conference of Building Officials.

21-15; 2102.2, Item 8

Mortar for Unit Masonry and Reinforced Masonry Other Than Gypsum. Standard Specifications C 161-44T and C 270-59T of the ASTM.

21-16; 2102.2, Item 8

Field Tests Specimens for Mortar. Test Standard of the International Conference of Building Officials.

21-17; 2102.2, Item 6; 2105.3.2, 2105.3.3

Test Method for Compressive Strength of Masonry Prisms. Standard Test Method E 447-80 of the ASTM.

21-18; 2102.2, Item 9; Table 21-B

Method of Sampling and Testing Grout. Standard Method C 1019-84 of the ASTM.

21-19; 2102.2, Item 9

Grout for Masonry. Standard Specification C 476-83 of the ASTM.

21-20; 2102.2, Item 8

Standard Test Method for Flexural Bond Strength of Mortar Cement. Test Standard of the International Conference of Building Officials.

CHAPTER 22

22-1; 1808.6.1, 1808.7.1, 2202.1

Material Specifications for Structural Steel. Standard Specifications A 27, A 36, A 48, A 53, A 148, A 242, A 252, A 283, A 307, A 325, A 336, A 441, A 446, A 449, A 490, A 500, A 501, A 514, A 529, A 563, A 569, A 570, A 572, A 588, A 606, A 607, A 611, A 618, A 666, A 668, A 690, A 715 and A 852 of the ASTM.

CHAPTER 23

23-1; 2302.1, 2303.1

Classification, Definition and Methods of Grading for All Species of Lumber. Standard Methods D 245-70 and D 2555-70 of the ASTM, Handbook No. 72 of the United States Department of Agriculture, American Softwood Lumber Standard PS20-70 and National Grading Rule for Dimension Lumber of the National Grading Rule Committee.

23-2; 2302.1, 2303.1, 2303.2, 2314.1, 2314.3; Tables 23-B, 23-J-1, 23-K-1, 23-S-2, 23-T-1; 2502

Construction and Industrial Plywood. Products Standard PS 1-83 of the United States Department of Commerce, and National Bureau of Standards Calculation Diaphragm Action, an Engineering Standard of the International Conference of Building Officials.

23-3; 2302.1, 2303.1, 2303.2, 2314.3; Tables 23-J-1, 23-K-1, 23-Q and 23-S-2; 2502

Wood-Based Structural-Use Panels. Product Standard PS 2-92 of the United States Department of Commerce and the American Plywood Association.

23-4; 2302.1, 2303.1, 2320.5, 2326.6

Wood Particleboard. American National Standard for Wood Particleboard, ANSI** A208.1-1989.

23-5; 201.2, 207, 2301

Fire-retardant-treated Wood Tests on Durability and Hygroscopic Properties. Standard Test Methods D 2898-81 and D 3201-79 of the ASTM and Standards C 20-83 and C 27-83 of the American Wood Preservers Association.

23-6; 207, 2303.1, 2304.3.3

Fire-retardant-treated Wood. National Design Specification for Wood Construction Policy on Design Values for Fire-retardant-treated Lumber (1982), including 1982 Supplement, American Forest and Paper Association.

CHAPTER 24

24-1; 2401.2, 2401.4

Flat Glass. Standard Specification C 1036-85 of the ASTM.

24-2; 2401.2, 2401.4, 2406.2, 2406.3, 2406.5, 2408.1

Safety Glazing. Safety Standard for Architectural Glazing Materials (16 C.F.R., Part 1201) of the United States Consumer Product Safety Commission and Performance Specifications and Methods of Test for Transparent Safety Glazing Material Used in Buildings. ANSI Z97.1-1975 of the American National Standards Institute, Inc.

CHAPTER 25

25-1; 2502

Plastic Cement. Test Standard of the International Conference of Building Officials.

25-2; 2502, Table 25-A

Metal Suspension Systems for Acoustical Tile and for Lay-in Panel Ceilings. Standard Specification C 635-69 and Standard Recommended Practice C 636-69 of the ASTM.

CHAPTER 26

26-1; 601.3, 2602.4, 2602.5.2

Test Method to Determine Potential Heat of Building Materials. Test Standard of the International Conference of Building Officials.

26-2; 601.3, 2602.4

Test Method for the Evaluation of Thermal Barriers. Standard of the International Conference of Building Officials.

26-3; 601.3, 2602.6

Room Fire Test Standard for Interior of Foam Plastic Systems. Test Standard of the International Conference of Building Officials.

26-4; 601.3, 2602.5.2

Method of Test for the Evaluation of Flammability Characteristics of Exterior, Nonload-bearing Wall Panel Assemblies Using Foam Plastic Insulation. Test Standard of the International Conference of Building Officials.

26-5; 217, 2603.1.6

Chamber Method of Test for Measuring the Density of Smoke from the Burning or Decomposition of Plastic Materials. Standard Test Method D 2843-70 of the ASTM.

26-6; 201.2, 217, 2603.1.6

Test Method for Ignition Properties of Plastics. Standard Test Method D 1929-68 (1975) of ASTM.

26-7; 201.2, 217, 2603.1.6

Method of Test for Determining Classification of Approved Light-transmitting Plastics. Standard Test Method D 635-74 of ASTM.

CHAPTER 31

31-1; Appendix 3122.2

Flame-retardant Membranes. Test Standard of the International Conference of Building Officials.

Part III-Recognized Standards

TITLE AND SOURCE ---------------------- SECTION REFERENCE

CHAPTER 6

Fire Test Standard for Insulated Roof Deck Construction. 601.3
Factory Mutual Standard.

Fire Test Standard for Insulated Roof Deck Construction. 601.3
Underwriters Laboratories Inc. 1256 (January, 1985).

CHAPTER 7

Perlite Loose-fill Insulation. 703.4
C 549-81 of the ASTM.

Vermiculite Loose-fill Insulation. 703.4
C 516-80 of the ASTM.

Fire Doors and Windows. 703.4

American National Standard ANSI/National Fire Protection Association 80-1990

Gypsum Base for Veneer Plaster and Gypsum Veneer. 703.4
C 587-91 and C 588-92 of the ASTM.

Lightweight Aggregates for Structural and Insulating Concrete. 703.4
C 330-89 and C 332-87 of the ASTM.

Lightweight Aggregates for Concrete Masonry Units. 703.4
C 331-89 of the ASTM.

Fire Dampers. 703.4
UL 555, January 1990.

Ceiling Dampers. 703.4
UL 555C, December 1992.

Leakage Rated Dampers for Use in Smoke Control. 703.4
UL 555S, September 1983.

Heat Response Links for Fire Protection Service. 703.4
UL 33, October 1987.

Limit Controls. 703.4
UL 353, January 1993.

CHAPTER 12

Ventilation for Acceptable Indoor Air Quality. 1205.2
ANSI/ASHRAE 62-1989, including ANSI/ASHRAE Addendum 62a-1990.

CHAPTER 15

Materials for Use in Construction of Built-up Roof Coverings. 601.3, 1501.1

Standard Specification 55-A 1983 (Reprinted December 24, 1985) of the Underwriters Laboratories Inc.

Roofing Asphalt and Coal Tar Bitumen. 1501.1
D 312-84 and D 450-78 (1984) of the ASTM.

Class C Sheet Roofing and Shingles Made from Asphalt Organic Felt. 1501.1

Standard Specification 55-B, October 5, 1983, of the Underwriters Laboratories Inc.

Sheet Metals. 1501.1
A 570-92 and A 611-92 of the ASTM.

Corrosion-resistant Metals. 1501.1
A 219-59 and A 239-41 of the ASTM.

Asbestos-Cement Shingles. 1501.1
C 222-60 of the ASTM.

Slate Shingles. 1501.1
C 406-57T of the ASTM.

Wire. 1501.1
B 134-62, B 211-63 and B 250-62 of the ASTM.

CHAPTER 16

Guide Specifications for the Design Loads of Metal Flagpoles. 1603.2
ANSI/NAAMM FP1001, 1990.

Minimum Design Loads for Buildings and Other Structures. 1603.2
ASCE 7-88-Chapter 6.

Structural Standards for Steel Antenna Towers and 1603.2
Antenna Supporting Structures.
ANSI EIA/TIA 222-2E, 1991.

CHAPTER 19

Concrete Aggregates. 1903.2.3
C 33-86 of the ASTM.

Lightweight Aggregates for Structural and Insulating Concrete. 703.4, 1903.2.3
C 330-85 and C 332-83 of the ASTM.

Reinforcing Bars for Concrete. 1903.2.5

A 615-87, A 616-87, A 617-87, A 706-86, A 767-M-88 and A 775-M-88 of the ASTM.

Smooth Steel Wire for Spiral Reinforcement 1903.2.6
A 82-85 of the ASTM.

Fabricated Deformed Steel Bar Mats. 1903.2.5
A 184-86 of the ASTM.

Welded Steel Wire Fabric and Deformed Steel Wire. 1903.2.5
A 185-85, A 496-85 and A 497-86 of the ASTM.

Steel Wire, Strand and Bar for Prestressing. 1903.2.5
A 416-88, A 421-80 and A 722-88 of the ASTM.

Air-entraining Admixtures for Concrete. 1903.2.6
C 260-86 and C 1017-85 of the ASTM.

Chemical Admixtures for Concrete. 1903.2.6
C 494-92 and C 1017-85 of the ASTM.

Fly Ash and Raw or Calcined Natural Pozzolans for Use as Admixtures 1903.2.6
in Portland Cement Concrete.
C 618-92 of the ASTM.

Concrete Tests. 1903.2.7
C 31-85, C 39-86, C 42-84a, C 172-82 and C 192-81 of the ASTM.

Splitting Tensile Strength. 1903.2.7
C 496-85 of the ASTM.

Specification for Expansive Hydraulic Cement. 1903.2.2
C 845-90 of the ASTM.

CHAPTER 21

Sampling and Testing Concrete Masonry Units. 2102.2
C 140-90 of the ASTM.

Structural Clay Facing Tile. 2102.2
C 212-86 of the ASTM.

Structural Clay Load-bearing Wall Tile and Standard Methods of 2102.2
Sampling and Testing Structural Clay Tile.
C 34-84 and C 112-70 of the ASTM.

Structural Clay Nonload-bearing Tile. 2102.2
C 56-71 (Reapproved 1986) of the ASTM.

Structural Clay Non-Loadbearing Screen Tile. 2102.2
C 530-86 of the ASTM.

Cast Stone. 2102.2
ACI 704-44 of the American Concrete Institute.

Aggregate for Masonry Mortar. 2102.2
C 144-89 of the ASTM.

Aggregates for Masonry Grout. 2102.2
C 404-87 of the ASTM.

Lightweight Aggregates for Concrete Masonry Units. 2102.2
C 331-89 of the ASTM.

Sampling and Testing Brick. 2102.2
C 67-87 of the ASTM.

Ceramic Glazed Structural Clay Tile, Facing Brick and Solid Masonry Units. 2102.2
C 126-86 of the ASTM.

Standard Test Method for Drying Shrinkage of Concrete Block. 2102.2
C 426-70 (Reapproved 1988) of the ASTM.

CHAPTER 22

Structural Rivet Steel. 2202.1
A 502-65 of the ASTM.

Specification for the Design of Cold-formed Stainless Steel 2202.1
Structural Members.
American Society of Civil Engineers, ANSI/ASCE-8-90.

Seismic Provisions for Structural Steel Buildings. 2202.1
American Institute of Steel Construction, June 1992

CHAPTER 23

Spruce-Pine-Fir, Douglas Fir-Larch (North), Hem-Fir Tables 23-A-1, 23-A-2

(North), Northern Species, Eastern Hemlock-Tamarack (North), Western Hemlock (North), Coast Sitka Spruce, Ponderosa Pine, Western Cedars (North), Western White Pine and Red Pine.

Standard Grading Rules for Canadian Lumber, United States Edition (August 1991).

Douglas Fir-Larch (Coast Region), West Coast Hemlock, Tables 23-A-1, 23-A-2

Spruce-Pine-Fir (South), Western Cedars, Western Red Cedar, White Fir and Sitka Spruce.

Standard Grading Rules No. 17 of the West Coast Lumber Inspection Bureau (September 1991).

Douglas Fir, Engelmann Spruce, Sitka Spruce, Tables 23-A-1, 23-A-2

Mountain Hemlock, Western Hemlock, Idaho White Pine, Incense Cedar, Western Red Cedar, Port Oxford Cedar, Alaska Cedar, Radiata Pine, Sugar Pine, True Cedars, Aspen and Red Alder.

Western Lumber Grading Rules (1991) of the Western Wood Products Association.

Eastern White Pine, Red Pine, Eastern Spruce, Jack Pine, Table 23-A-1

Eastern Cottonwood, Balsam Fir, Aspen (Bigtooth Quaking), Yellow-Poplar, Eastern Hemlock and Tamarack.

Grading Rules of the Northern Hardwood and Pine Manufacturers Association, Inc. (1978).

Southern Pine. Tables 23-A-1, 23-A-2

Grading Rules for Southern Pine Lumber of the Southern Pine Inspection Bureau (1991).

Redwood. Table 23-A-1

Standard Specifications for Grades of California Redwood Lumber (December 1990) of the Redwood Inspection Service.

Eastern Woods, Eastern Spruce, Balsam Fir, Eastern White Pine, Table 23-A-1

Northern Pine, Eastern Hemlock-Tamarack, Aspen, Eastern Softwoods, Eastern Hemlock, Spruce-Pine-Fir (South), Red Pine and Northern White Cedar.

Standard Grading Rules of the Northeastern Lumber Manufacturers Association, Inc. (1991).

Structural Glued-laminated Timber. 2303.1

ANSI/AITC A190.1-1992, American National Standards Institute; D 3737-89a of the ASTM.

Structural Glued-laminated Timbers: Softwood and Hardwood Species. 2303.1

Standard Specifications for Structural Glued-laminated Timber of Softwood Species, 117-88-Manufacturing, and 117-87-Design, American Institute of Timber Construction, and Standard Specifications for Hardwood Glued-laminated Timber (1985), American Institute of Timber Construction.

Preservative Treatment by Pressure Processes and Quality Control Standards. 2303.1

C1-90, C2-90, C3-90, C4-90, C9-90, C14-90, C15-91, C16-91, C22-91, C23-84, C24-86, C28-90 and M4-90, of the American Wood Preservers Association.

Wood Poles. 2303.1

ANSI 05.1-1972 of the American National Standards Institute, Inc.

Round Timber Piles. 2303.1
D 25-87 of the ASTM.

Adhesives. 2303.1

D 2559-76 of the ASTM
AFG-01 September 1974 American Plywood Association.

Exterior (Wet Use) and Interior (Dry Use). 2303.1

Standard Specification for Adhesives for Structural Laminated Wood Products for Use Under Exterior (Wet Use) Exposure Conditions.

D 2559-84 of the ASTM.

Standard Specification for Protein-Based Adhesives for Structural 2303.1

Laminated Wood Products for Use Under Interior (Dry Use) Exposure Conditions.

D 3024-84 of the ASTM.

Test for Glue Joints in Laminated Wood Product. 2303.1
D 1101-81 of the ASTM.

Tests for Structural Glued-laminated Timber. 2303.1

Inspection Manual, AITC 200-92, of the American Institute of Timber Construction referenced in American National Standard ANSI/AITC A190.1-92 and Standard Method of Testing D 905-49 (R81) of the ASTM.

Cellulosic Fiberboard. 2303.1
American National Standard ANSI/AHA A194.1-1985.

Hardboard Siding. 2303.1
American National Standard ANSI/AHA A135.6-1989.

Design Values for Structural Glued-laminated Timber. 2303.1

Determination of Design Values for Structural Glued-laminated Timber ASTM D 3737-89a, AITC 500-91, American Institute of Timber Construction.

Prefabricated Wood I-Joists. 2303.1

Standard Specification for Establishing and Monitoring Structural Capacities of Prefabricated Wood I-Joists.

D 5055-90 of ASTM.

Visually Graded Dimension Lumber. 2303.1

Establishing Allowable Properties for Visually-graded Dimension Lumber from In-Grade Tests of Full-size Specimens.

D 1990-91 of the ASTM.

Establishing Structural Grades and Related Allowable Properties for 2303.1

Visually Graded Lumber.

D 245-88 of the ASTM.

Standard Test Methods for Establishing Clear Wood Strength Values. 2303.1
D 2555-88 of the ASTM.

CHAPTER 25

Plaster Bonding Agents. 2502

United States Government Military Specification MIL-B-19235 (Docks) December 12, 1965; the 1965 Edition of Standard Specifications of the California Lathing and Plastering Contractors Association, and the Recommendations of the Gypsum Association.

Adhesives for Fastening Gypsum Wallboard to Wood Framing. 2502
C 557-73 of the ASTM.

Perlite, Vermiculite and Sand Aggregates for Gypsum Plaster. 2502
C 35-70 of the ASTM.

Metal Lath, Wire Lath, Wire Fabric Lath and Metal Accessories. 2502

Standard Specification A 42.4-1955 of the ANSI and Specification 2.6.73 of the California Lathing and Plastering Contractors Association.

Exterior Gypsum Soffit Board. 2502
C 931-91 of the ASTM.

Steel Drill Screws for the Application of Gypsum Board or Metal Plaster Bases. 2502
C 1002-88 of the ASTM.

Gypsum Wallboard Tape and Joint Compound. 2502
C 475-70 and C 474-73 of the ASTM.

Gypsum Backing Board. 2502
C 442-92 of the ASTM.

Gypsum Lath. 2502
C 37-92 of the ASTM.

Gypsum Plasters. 2502
C 28-92 of the ASTM.

Gypsum Sheathing Board. 2502
C 79-92 of the ASTM.

Gypsum Wallboard. 2502
C 36-92 of the ASTM.

Keene's Cement. 2502
C 61-70 of the ASTM.

Water-resistant Gypsum Backing Board. 2502
C 630-92 of the ASTM.

Gypsum Base for Veneer Plaster and Gypsum Veneer Plaster. 2502
C 588-92 and C 587-73 of the ASTM.

Lime. 2502
C 6-49 (1968) and C 206-49 (1968) of the ASTM.

Testing Gypsum and Gypsum Products. 2502
C 22-50 (R74), C 472-73 and C 473-92 of the ASTM.

Application of Gypsum Base for Veneer Plaster and Gypsum Veneer Plaster. 2502
C 843-76 and C 844-79 of the ASTM.

Nails for the Application of Gypsum Wallboard, 2502

Gypsum Backing Board and Gypsum Veneer Base.

C 514-77 of the ASTM.

CHAPTER 31

Fireclay Refractories. 3102.2
C 27-60 of the ASTM.

APPENDIX CHAPTER 10

10-5; See Section 1022 and Uniform Building Security Code

Tests for Doors and Locking Hardware Used for Security. Standard of the International Conference of Building Officials.

10-6; See Section 1022 and Uniform Building Security Code

Tests for Window Assemblies. Standard of the International Conference of Building Officials.

APPENDIX CHAPTER 12

Laboratory Determination of Airborne Sound Appendix 1221.1

Transmission Class (STC).

E 90-83 and E 413-73 (1980) of the ASTM.

Impact Sound Insulation. Appendix 1221.1
E 492-77 of the ASTM.

Airborne Sound Insulation Field Test. Appendix 1221.1
E 336-84 of the ASTM.

APPENDIX CHAPTER 33

Moisture-Density Relations of Soils and Soil Aggregate Mixtures. Appendix 3312
D 1557-78 of the ASTM.

In Place Density of Soils by the Sand Cone Method. Appendix 3312
D 1556-82 of the ASTM.

In Place Density of Soils by the Rubber-Balloon Method. Appendix 3312
D 2167-66 (1977) of the ASTM.

In Place Density of Soil by the Drive-Cylinder Method. Appendix 3312
D 2937-71 (1976) of the ASTM.

In Place Moisture Content and Density of Soils by Nuclear Methods. Appendix 3312
D 2922-81 and D 3017-78 of the ASTM.

Go to Table of Contents
Go to previous section: 3502
Commercial Asbuilts: BOMA Asbuilt | Definitions | Projects | Project Types | FAQ | Useful links
Residential Asbuilts: Projects | Asbuilt Services | FAQ
Contact | Copyright | Privacy Policy | Site Map | News